Skip to main contentSkip to footerOpens in a new tab.
Digital LED Sync Clocks & Systems Manufacturer in China

Examination spaces

Exam Room Clock Layout and Pre-Exam Checks

Give every candidate a clear view of the same actual time. Plan the clock positions around the seated audience, then check readability and time agreement before each examination session.

Start with the seats

A clock on the front wall is not automatically visible from every desk. Check the far corners, obstructed rows and separate access-arrangement rooms.

What must every seated candidate be able to see?

Each candidate needs a clear view of the actual time from their assigned seat. Choose the display and its location together: a large display behind a column is less useful than a smaller, correctly positioned one with a clear sightline. Verify the installed result rather than relying on an advertised viewing distance alone.

For centres following JCQ Instructions for Conducting Examinations, section 11.8 of the edition effective 1 September 2026 requires visibility of the actual time, prohibits countdown and count-up clocks, and calls for checking that clocks show the same time before the examination. These are JCQ examination rules, not a worldwide rule or a requirement to buy a particular synchronization system.

How should clocks and exam information boards be separated?

The clock shows actual time; the examination information board communicates the session details. Keep both readable without treating the clock as a substitute for the written start and finish times. For examinations governed by JCQ, section 11.9 addresses the information to be displayed, including the starting and finishing times.

Decide whether seconds are useful for the room and whether the added digits reduce the prominence of hours and minutes. Compare four-digit and six-digit displays without assuming that one format is mandatory for every examination.

How do we check every seat before choosing clock positions?

Use a seat-by-seat sightline check under the lighting and furniture arrangement that will be used during the exam. Start at the furthest seats, then test side angles and rows near obstructions. Record which clock each seat relies on and resolve any gap before approving the layout.

Example layout check, not an installation drawing

Front wall: Clock A + separate examination information board

A1
B1
C1
A2
B2
C2
A3
B3
C3

Rear/side position: Consider Clock B only where the seat checks show that Clock A cannot be read clearly. Both displays must agree.

Seat or zoneVisible clock IDObstruction or glareAction and recheck
Front rowsRecord on siteCheck height and angleRecord result
Rear cornersRecord on siteCheck digit visibilityRecord result
Side rowsRecord on siteCheck oblique viewRecord result
Separate roomRecord on siteCheck its own seating planRecord result

Keep the room name, seating-plan revision, checker and date with the completed record. Recheck after moving desks, changing lighting or adding partitions.

What should be checked before each exam session?

Confirm the displayed time, visibility and operating condition before candidates enter. A successful installation check does not establish readiness for every later session: power loss, an incorrect local-time setting or a moved display can change the result. Assign a named person to perform and record the check.

  1. Confirm the correct local time, date-related settings and any seasonal time change.
  2. Compare all room displays against the centre's agreed reference and check that they agree.
  3. Check power and synchronization status using the equipment's documented indicators.
  4. Walk the seating layout for glare, obstructions and legibility.
  5. Confirm the written examination information independently of the clock display.
  6. Record exceptions and resolve them through the centre's examination procedure before use.

If a fault appears during an examination, follow the examination authority's incident procedure. Do not improvise a new timing rule, change the announced finishing time or treat a general clock guide as an invigilator's instruction.

What changes when several rooms share one time reference?

A shared reference can reduce manual setting work across rooms, but each display still needs a local readiness check. The network or distribution method, power supply and local-time configuration must work together. A synchronized clock does not by itself prove visibility, availability or compliance with an examination authority's procedures.

For a broader campus project, see higher-education clock applications. For school-wide spaces beyond the examination room, see K-12 education clock layouts. Those projects also include corridors, offices and other rooms with different viewing tasks.

What information helps us specify the displays?

Provide a room plan, seating positions, mounting constraints, expected lighting, available power and permitted synchronization connection. Identify any separate rooms and the examination rules your centre follows. Those inputs allow display options to be reviewed without guessing readability or promising unsupported model features.

  • Room dimensions, ceiling height and preferred mounting positions.
  • Seating-plan variations and the most difficult viewing positions.
  • Digital or analog preference, with hours/minutes prominence confirmed.
  • Available cabling, network access and responsibility for the reference time.
  • Pre-session checks, fallback arrangements and maintenance access.

Plan the room before selecting the clocks

Browse the clock catalogues or send the seating plan and project requirements to HC Electronics.

Discuss an examination room

Reference: JCQ Instructions for Conducting Examinations, effective 1 September 2026, sections 11.8 and 11.9. Check the rules applicable to your examination and session.